Formulations

UV FOG (Form on Gasket) 41764A is an EB/UV curable product that provides excellent adhesion to shaft seals, oil seals, metals, glass, ceramics and plastics. Can be used as a Form-in-place gasket in oil and coolant systems. Typical applications include Engine covers, Oil pans and other fluid seal systems.

DEACTIVATOR FOR UV FOG, 500 GRAMS

Nuts N’ Bolts® 410 is a single component, low viscosity anaerobic adhesive/sealant designed especially for wicking applications. It has the ability to penetrate porous structures and cracks by capillary action, filling voids as large as 0.005 in.

Rust Inhibitor 40 is an effective corrosion remover and rust preventative which leaves a protective finish for up to 1 year. Produces a clean, dry surface that can be painted, plated or powder coated afterward with no pre-cleaning. Not for use with zinc plated or magnesium items. Rust Inhibitor 40 is used on rusted steel when only a minimum surface preparation is practical. Rust Inhibitor 40 protects, cleans and leaves a protective coating.

Grenade Igniter Case Sealant 40995 is a single component anaerobic thread locking and sealing adhesive. Grenade Igniter Case Sealant 40995 is a low viscosity penetrating material that works by capillary action between mating surfaces. The cured adhesive is a high-performance thermoset plastic suitable for temperatures up to 400°F (204°C). Grenade Igniter Case Sealant 40995 cures quickly at room temperature without the need for surface activators or heat to join threaded assemblies. Fixturing strength develops in five minutes, or within 10 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 60 milliwatts/cm² to insure proper cure.

HASA 39781 is a single-component, anaerobic, structural adhesive designed for bonding rigid assemblies. HASA 39781 cure is accomplished when mating surfaces including metal, glass and ceramics are joined together. Accelerated cures are possible with the application of primers or by a short, low temperature heat cycle. Upon cure, HASA 39781 is a highly crosslinked thermoset plastic with excellent properties over a wide range of conditions.

Tuffbond® 395 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond® 395 will change from amber to a reddish brown upon cure. Bonding the voice coil to the cone has been a challenge for engineers, specifically when the adhesive temperature resistance requirement is above 200°F (93°C). Two component epoxy systems have been most commonly used for this application, but limitations such as mixing ratio, cure speed, potential solidification in equipment and static mixers and the need for equipment flushing solvents have made Tuffbond® 395 more practical.

Tuffbond® 394 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond® 394 will change from amber-yellow to a reddish brown upon cure. Bonding the voice coil to the cone has been a challenge for engineers, specifically when the adhesive temperature resistance requirement is above 200°F (93°C). Two component epoxy was commonly used for this application, but limitations such as mixing ratio, cure speed, potential solidification in equipment and the need for equipment flushing solvents have made Tuffbond® 394 more practical.

Hernon’s Bullet Tip ID Coating is the latest technology in ammunition identification, specifically formulated for using inkjet applications, offering advances in adhesion, scratch resistance, and superior print quality. This single-component, solvent-free, UV or LED-curable coating ensures fast curing time and cost-efficient processing, combining with Hernon patented dispensing technologies, making it the ideal solution for high-volume ammunition marking with simple operation.

Typical applications include:

• Ammunition identification and branding
• Military and commercial bullet marking
• High-speed production environments requiring rapid curing

Traditional paints (solvent-based or water-based) are being replaced by modern UV LED curable acrylates. Now the drying time is just a few seconds under UV LED light. Full cure will be reached in 24 hours.

Product Benefits

• Excellent adhesion to bullet tips
• Scratch-resistant for durability
• High-definition print quality and uniformity
• Solvent-free, environmentally friendly formulation
• Single-component system for easy application
• UV or LED cured for instant drying and rapid processing
• Available in multiple colors that matched to the Federal Standard 595C- or RAL for easy identification

Porosity Sealant (HPS) 38374R is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The required addition of HPS Initiator activates the dual-cure system enabling the system to cure anaerobically at room temperature or at elevated temperatures. The cured, hardened resin exhibits superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic or plastic molecules) in the part are filled by low viscosity resin during vacuum application. Sealed micro-pores cure without shrinkage to a tough, cross-linked, thermoset polymer, permanently sealing the work piece. Residual adhesive film is washed from the part surfaces by water during the rinsing cycle. The parts leave the impregnating process without surface residue and can then be used in production within a short period of time. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating material (like acids) or painting prep solvents that could otherwise bleed out of the pores causing finishes to discolor, blister, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Hernon® Porosity Sealant (HPS) Surfactant 381001 is a single component product designed to be used as wetting agent.

Primer 37824 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 37824 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Fusionbond® 375 is a highly thixotropic, two component, room temperature curing, 1:1 ratio, methacrylate adhesive system. Fusionbond® 375 is formulated to provide fixturing strength within 7 to 10 minutes. This adhesive product forms resilient bonds and maintains its strength over a wide range of temperatures. Fusionbond® 375 is suitable for bonding a variety of substrates with a minimum of surface preparation. Fusionbond® 375 provides toughness at temperatures from -67 to 250°F. Recommended substrates: PVC, acrylic, ABS, stainless steel, and some types of fiberglass.

Hernon® has taken the excellent bond strength of Fusionbond adhesive family and merged it with the simplicity of a two-component, no-mix curing system to create Fusionbond® 374. Fusionbond® 374 is a 100% solid, room temperature cure, versatile structural adhesive which is used in conjunction with Hernon® Activator 56, 15 or 16. This formulation will offer rapid, high strength and high impact resistant bonds to a variety of substrates within minutes. Designed for a wide variety of substrates, Fusionbond® 374 offers excellent temperature and chemical resistance. The two-component, no-mix system allows controlled assembly ideal for production and repair applications. A structural bond develops within minutes.

Fusionbond® 371 is a two components methacrylate adhesive. It is specially formulated for structural bonding of thermoplastics, metal, wood and composite assemblies. Fusionbond® 371 is an excellent choice for composite bonding applications in the marine, automotive and construction industries because it requires virtually no surface preparation. Fusionbond® 371 provides toughness at temperatures from -67 to 250°F.

Fusionbond® 370 is a two components methacrylate adhesive. It is specially formulated for structural bonding of thermoplastics, metal, wood and composite assemblies. Fusionbond® 370 is an excellent choice for composite bonding applications in the marine, automotive and construction industries because it requires virtually no surface preparation. Fusionbond® 370 provides superior toughness at temperatures from -67 to 250°F.

Brake Bonder 362 is a black heat curing, nitrile/phenolic solvent-based adhesive. Cured Brake Bonder 362 furnishes excellent resistance to thermal shock, chemicals, and water. The cured bond withstands temperatures exceeding 600°F (315°C). The primary application for Brake Bonder 362 is bonding brake, clutch, and other friction materials to metal.

Hernon Voice Coil Bonder 360 is a single component, black, heat cure adhesive formulated for bonding and coating voice coil components and high-temperature lamination. The cured bond withstands temperatures exceeding 600°F (316°C).

Supertacker® 357 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 357 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 357 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.

Supertacker® 353 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 353 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 353 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.