Formulations

HASA 39781 is a single-component, anaerobic, structural adhesive designed for bonding rigid assemblies. HASA 39781 cure is accomplished when mating surfaces including metal, glass and ceramics are joined together. Accelerated cures are possible with the application of primers or by a short, low temperature heat cycle. Upon cure, HASA 39781 is a highly crosslinked thermoset plastic with excellent properties over a wide range of conditions.

Grenade Igniter Case Sealant 40995 is a single component anaerobic thread locking and sealing adhesive. Grenade Igniter Case Sealant 40995 is a low viscosity penetrating material that works by capillary action between mating surfaces. The cured adhesive is a high-performance thermoset plastic suitable for temperatures up to 400°F (204°C). Grenade Igniter Case Sealant 40995 cures quickly at room temperature without the need for surface activators or heat to join threaded assemblies. Fixturing strength develops in five minutes, or within 10 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 60 milliwatts/cm² to insure proper cure.

Nuts N’ Bolts® 410 is a single component, low viscosity anaerobic adhesive/sealant designed especially for wicking applications. It has the ability to penetrate porous structures and cracks by capillary action, filling voids as large as 0.005 in.

UV FOG (Form on Gasket) 41764A is an EB/UV curable product that provides excellent adhesion to shaft seals, oil seals, metals, glass, ceramics and plastics. Can be used as a Form-in-place gasket in oil and coolant systems. Typical applications include Engine covers, Oil pans and other fluid seal systems.

Porosity Sealant (HPS) 41814 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The hardened resins exhibit superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic plastic molecules) in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage when exposed to elevated temperature to form tough cross-linked thermoset polymer, permanently sealing the workpiece. Residual adhesive film is water-washed from the part surfaces during rinsing. The parts leave the impregnating process without surface residue and can then be used in production immediately. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Nuts N’ Bolts® 420 is a single component anaerobic thread locking material, which is thixotropic and develops low strength for easy disassembly. The product cures when confined in the absence of air between close fitting metal surfaces.

Porosity Sealant (HPS) 994 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The hardened resins exhibit superior chemical resistance and higher temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic plastic molecules) in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage when exposed to elevated temperature to form tough cross-linked thermoset polymer, permanently sealing the workpiece. Residual adhesive film is water-washed from the part surfaces during rinsing. The parts leave the impregnating process without surface residue and can then be used in production immediately. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Nuts N’ Bolts® 428 is a single component anaerobic threadlocking compound designed for heavy duty applications subject to operating temperatures to 450°F (232°C). The product delivers high strength locking and sealing on screws, nuts, bolts, studs and fittings. Excellent break-loose and prevailing torque values assure maximized resistance to transverse vibration loosening at elevated temperatures. Meets requirements of CID A-A-59720 Grade HT

Dripstop® 912 provides maximum solvent resistance on threaded fittings and pipe up to 3” in diameter. It is recommended for refrigeration systems and service with strong chemicals. Dripstop® 912 is not for slip fitted tube joints. Dripstop® 912 has excellent solvent resistance and withstands temperatures to 300°F (149°C). This product is not recommended for use on plastic piping.

Gasket Replacer® 910 is a single component room temperature cure gel-like anaerobic gasket compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, Gasket Replacer 910 provides a thin, flexible, solvent, and temperature-resistant seal. Gasket Replacer 910 is a recommended alternative to Gasket Eliminator Flange Sealant. Designed for metal closures Gasket Replacer offers a semi-flexible, anaerobic seal for flanges, similar to Loctite 515 and Loctite 518. Gasket Replacer's gel-like consistency can fill minor gaps and imperfections in flange surfaces and when fully cured, this sealant resists significant pressure. Known as a form-in-place gasket, this sealant adapts to the size and shape of the flange allowing a wide variety of uses including oil seals, engine housings and transmission flanges.

Fusionbond® 370 is a two components methacrylate adhesive. It is specially formulated for structural bonding of thermoplastics, metal, wood and composite assemblies. Fusionbond® 370 is an excellent choice for composite bonding applications in the marine, automotive and construction industries because it requires virtually no surface preparation. Fusionbond® 370 provides superior toughness at temperatures from -67 to 250°F.

Fusionbond® 371 is a two components methacrylate adhesive. It is specially formulated for structural bonding of thermoplastics, metal, wood and composite assemblies. Fusionbond® 371 is an excellent choice for composite bonding applications in the marine, automotive and construction industries because it requires virtually no surface preparation. Fusionbond® 371 provides toughness at temperatures from -67 to 250°F.

Hernon® has taken the excellent bond strength of Fusionbond adhesive family and merged it with the simplicity of a two-component, no-mix curing system to create Fusionbond® 374. Fusionbond® 374 is a 100% solid, room temperature cure, versatile structural adhesive which is used in conjunction with Hernon® Activator 56, 15 or 16. This formulation will offer rapid, high strength and high impact resistant bonds to a variety of substrates within minutes. Designed for a wide variety of substrates, Fusionbond® 374 offers excellent temperature and chemical resistance. The two-component, no-mix system allows controlled assembly ideal for production and repair applications. A structural bond develops within minutes.

Tuffbond® 321 is a flexible, low viscosity, general purpose resin system used for casting, potting, and encapsulating of electrical and electronic components. This unique product has been formulated to combine ease in handling with optimum physical, thermal and electrical insulation properties.

Rust Eliminator 32 is a new revolutionary product for eliminating old rust and preventing new rust on steel parts. Rust is chemically transformed into an inert, non-corrosive coating.

Dripstop® 940 is a thread sealant, which contains Teflon®, and for use on inactive metals such as stainless steel and aluminum used in chemical process piping. The properties of this Dripstop® prevents galling on Stainless Steel, Aluminum, and other metal pipe fittings. Dripstop® 940 is formulated to cure without the necessity of a primer. Dripstop® 940 has been shown to be compatible for use within diesel exhaust systems using DEF according to ISO-22241 through independent 3rd party verification. Dripstop® 940 withstands high pressures, sealing up to 250 psig steam at 400°F (204°C) continuous service while maintaining its chemical inertness. UL Classification – File MH14222 Classified by Underwriters Laboratories Inc.® for use in devices handling gasoline, petroleum oils, natural gas (pressure not to exceed 300 psig), butane and propane not exceeding 2 in. pipe size. 29R9.

Dissipator® 746 is a thermally conductive adhesive formulated for bonding electrical components to heat sinks or printed circuit boards. Fast room temperature cure combined with excellent heat dissipation for thermally sensitive components and controlled strength for service repair provide perfect replacement for tapes, epoxies, silicones, fasteners and mechanical clips. Typical applications include bonding transformers, transistors and other heat generating electronic components to printed circuit board assemblies or heat sinks.

Nuts N’ Bolts® 248 is a single component anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications requiring easy removal or adjustment.

SelfSealer® 616 is a high viscosity, tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 616 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

SelfSealer® 604 is a tough, pre-applied, non-hardening threaded sealant. When dried, it becomes a resilient, tight clinging, non-curing sealant for tapered or straight threads. It provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 604 is water based, non-toxic, safe and can be applied easily without special handling precautions. It provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.