Formulations

Hernon Dissipator 746D is a thermally conductive adhesive formulated for bonding electrical components to heat sinks or printed circuit boards. Fast room temperature cure combined with excellent heat dissipation for thermally sensitive components and controlled strength for service repair provide perfect replacement for tapes, epoxies, silicones, fasteners and mechanical clips. Typical Applications Typical applications include bonding transformers, transistors and other heat generating electronic components to printed circuit board assemblies or heat sinks.

Hernon Dissipator 745D is a thermally conductive room temperature cure adhesive that is designed for bonding electrical components to heat sink with a controlled gap. Dissipator 745D, through a special shimming property, insulates the component electrically while allowing thermal conductivity. This special shimming feature produces a constant gap of 0.005 in. to 0.006 in. between components. Product Benefits • No mixing required (eliminates errors in mixing ratio) • Room temperature cure. No heat required. • Eliminates screws and rivets for assembly. • Eliminates the air space between components. • High k factor for heat conductive application

Instantbond® 123 is a medium viscosity, state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 123 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 123 can bond a wide variety of surfaces including metals, thermoplastics, elastomers, ceramics, leather, cork, and paper. Notwithstanding the superior bonding capability of Instantbond® 123, it is NOT recommended for long-term glass to glass bonding applications.

Instantbond® 127 is a gel consistency single component, solvent-less, room temperature adhesive that sets in seconds when confined between two surfaces. The gel consistency allows for gap filling capability and prevents migration to unwanted areas.

Tuffbond® 305 is a modified epoxy adhesive that provides a very fast room temperature cure. Tuffbond® 305 exhibits very good moisture chemical and heat resistance. This very fast cure epoxy adhesive is specially formulated for rapid in-line assembly of loud speakers. Tuffbond® 305 is also recommended for bonding metals, wood, ceramics, etc., and can be used for potting and encapsulation of electrical and electronic components.

Nuts N’ Bolts® 128 is a single component, low strength thread locker designed for locking plastic and metal fasteners. Fixture time is about 5 minutes and adhesive can be pre or post applied. Any excess adhesive on the surface will cure and will not migrate to the other parts. Nuts N’ Bolts® 128 can be used as a low strength thread locker, bonder or tamper proofer for metal, polyester, nylon and many other thermo plastics materials.

Quantum® 156 is a single-component cyanoacrylate adhesive formulated for impact, thermal shock and peel resistance.

Porosity Sealant (HPS) 59801 is a low viscosity liquid sealant designed for sealing interfacial leak paths in flexible electronic assemblies. It may also be used to enhance dielectric strength or seal porosity in passive materials. The dual-cure system incorporated in HPS 59801 offers the advantage of elevated temperature curing or curing at room temperature. HPS 59801 is typically applied with a vacuum impregnation process that removes air from the internal void and then saturates the part with liquid sealant. In the absence of circulating air, the liquid rapidly polymerizes to form a tough, flexible, thermoset polymer that permanently seals gaps in the assembly. Excess liquid sealant is rinsed from the outside of the part with an aqueous solution effectively leaving no surface build up. Parts processed with HPS 59801 are sealed internally but remain cosmetically and dimensionally unchanged. Typical applications include sealing or unitizing over-molded electrical components against leakage of air, water, coolants, oils and other fluids. As a good insulator, HPS 59801 may also be used to improve the dielectric strength across gaps between high voltage conductors.

Mine Bonder 2000 is an anaerobic adhesive sealant which cures rapidly through large gaps with Hernon Primer 50 and will also provide rapid cure and dry fillets when exposed to high intensity ultraviolet light.

Nuts N’ Bolts® 227 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications.

Nuts N’ Bolts® 230 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N’ Bolts® 232 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N’ Bolts® 234 is a single component medium strength, anaerobic compound used to lock and seal coarse threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N’ Bolts® 237 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications.

Nuts N’ Bolts® 240 is a single component anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications requiring easy removal or adjustment.

Nuts N’ Bolts® 425 is a single component anaerobic thread locking material, which is thixotropic and develops medium to high strength. The product cures when confined in the absence of air between close-fitting metal surfaces.

Nuts N’ Bolts® 246 is a single component anaerobic compound used to lock and seal coarse threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Ultrabond® 740 is formulated for bonding glass to glass or glass to metals. Ultrabond® 740 is excellent for bonding tacking and potting many parts. Ultrabond® 740 provides an excellent bond, high light transmittance and a refractive index like glass. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.