Applications

Rust Inhibitor 40 is an effective corrosion remover and rust preventative which leaves a protective finish for up to 1 year. Produces a clean, dry surface that can be painted, plated or powder coated afterward with no pre-cleaning. Not for use with zinc plated or magnesium items. Rust Inhibitor 40 is used on rusted steel when only a minimum surface preparation is practical. Rust Inhibitor 40 protects, cleans and leaves a protective coating.

Primer 46 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 46 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C.

Grenade Igniter Case Sealant 47422 is a single component UV and anaerobic curing adhesive. Grenade Igniter Case Sealant 47422 is a low viscosity penetrating material that works by capillary action between mating surfaces. The cured adhesive is a high performance thermoset plastic suitable for temperatures up to 400°F (204°C). Grenade Igniter Case Sealant 47422 cures quickly at room temperature without the need for surface activators or heat to join assemblies. Fixturing strength develops in five minutes, or within 10 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 60 milliwatts/cm² to insure proper cure.

UV FOG (Form on Gasket) 68221 is an EB/UV curable product that provides excellent adhesion to shaft seals, oil seals, metals, glass, ceramics and plastics. Can be used as a Form-in-place gasket in oil and coolant systems. Typical applications include Engine covers, Oil pans and other fluid seal systems.

Ultrabond® 3443 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 3443 is excellent for bonding and tacking many parts. Ultrabond® 3443 can also be cured with heat above 200°F (93°C) or Activator 56 or 59. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Nuts N’ Bolts® 427 is a single component anaerobic thread locking material, which develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces.

SelfSealer® 622 is a tough, pre-applied, non-hardening threaded sealant. SelfSealer® 622 provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 622 is water based, non-toxic, safe and can be applied easily without special handling precautions. SelfSealer® 622 provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

Brake Bonder 362 is a black heat curing, nitrile/phenolic solvent-based adhesive. Cured Brake Bonder 362 furnishes excellent resistance to thermal shock, chemicals, and water. The cured bond withstands temperatures exceeding 600°F (315°C). The primary application for Brake Bonder 362 is bonding brake, clutch, and other friction materials to metal.

Gasket Replacer 907 is a single component room temperature cure, gel-like anaerobic gasketing compound formulated to provide instant sealing capabilities. Once cured between metal flanges, Gasket Replacer 907 maintains a thin and rigid seal while providing solvent and temperature resistance.

Fusionbond® 370 is a two components methacrylate adhesive. It is specially formulated for structural bonding of thermoplastics, metal, wood and composite assemblies. Fusionbond® 370 is an excellent choice for composite bonding applications in the marine, automotive and construction industries because it requires virtually no surface preparation. Fusionbond® 370 provides superior toughness at temperatures from -67 to 250°F.

Quantum® 150 UV is a single component, solventless, room temperature curing cyanoacrylate adhesive with light curing property. The presence of surface moisture and/or light (UV or Visible light) commence the cure of the adhesive. Quantum® 150 UV develops handling strength within seconds and full functional strength within minutes. Quantum 150 UV can bond a wide variety of surfaces including thermoplastics, elastomers. Product Benefits: • Rapid Cure: forms a strong bond by moisture curing at room temperature in less than a minute with contact pressure. • Light curing property: can be easily cured by irradiation with light. Blushing can be also prevented by UV curing. • Surfaces: will bond almost any combination of similar or dissimilar materials. • Easy Use: single component feature, eliminates any mixing. • Due to low viscosity, it can penetrate gaps between surfaces.

Ultrabond® 787 is a one component, thixotropic adhesive, which cures when exposed to ultraviolet radiation and/or visible light of sufficient intensity. Ultrabond® 787 is primarily used for bonding rigid and flexible PVC to polycarbonate where large gap filling capabilities and a flexible joint are desired. Its flexibility enhances the load bearing and shock absorbing characteristics of the bond area. It has also shown excellent adhesion to a wide variety of substrates including glass, many plastics and most metals.

Bullet Proof 650 is an environmentally friendly, single component, room temperature cure sealant and coating material. Bullet Proof 650 is formulated to waterproof and seal the interface between a bullet and cartridge. Bullet Proof 650 coats the inside of large shells to prevent the corrosive attack by the cartridge on the ignition powder.

HASA 66071 is a single component structural anaerobic adhesive formulated for bonding rigid assemblies at high temperatures. HASA 66071 cures when it is confined between mating surfaces. Hernon® Primer 50 accelerates the cure.

Nuts N’ Bolts® 97860 is a wicking anaerobic used for preassembled equipment and structures where penetration into fastener connection points is required. This product allows very simple preventive maintenance by permitting thread locking without dismantling equipment. The product “wicks” into voids by capillary action. Use Nuts N’ Bolts® 97860 to seal pores or pinhole porosity in welded seams, tanks, castings, or metal parts. The cured adhesive is a thermoset plastic suitable for temperatures up to 400°F (204°C), and exposure to most solvents.

Primer 37824 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 37824 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Activator 45 is solvent-free and designed to initiate the cure of Hernon® toughened acrylic adhesives. Since Activator 45 contains no solvents, no waiting time for solvent evaporation is needed prior to assembly.

Adhesion Promoter 42 is a single component product designed to improve adhesion to low surface energy plastics such as polyethylene, polypropylene, and Santoprene to similar substrates using Quantum® and Instantbond® adhesives.

Activator 51 is a solvent-free product that is designed to initiate the cure of Hernon® toughened acrylic adhesives. Since Activator 51 contains no solvents, no waiting time for solvent evaporation is needed prior to assembly.

Activator 56 is a single component, non-CFC solvent-based product, designed to promote the cure speed of Hernon® Structural Adhesive/Sealants. Activator 56 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. Especially recommended for applications with passive metals, inert surfaces or where large gaps are present.

Accelerator 48 is a solvent-based accelerator for instant adhesives. The accelerator is designed to speed the cure of Hernon cyanoacrylate adhesives. Accelerator 48 is used where increased cure speed of Hernon® cyanoacrylate adhesives is required. Especially recommended for applications involving printed circuit board wire tacking and tamper proofing of adjustable components.

Gasket Replacer® 910 is a single component room temperature cure gel-like anaerobic gasket compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, Gasket Replacer 910 provides a thin, flexible, solvent, and temperature-resistant seal. Gasket Replacer 910 is a recommended alternative to Gasket Eliminator Flange Sealant. Designed for metal closures Gasket Replacer offers a semi-flexible, anaerobic seal for flanges, similar to Loctite 515 and Loctite 518. Gasket Replacer's gel-like consistency can fill minor gaps and imperfections in flange surfaces and when fully cured, this sealant resists significant pressure. Known as a form-in-place gasket, this sealant adapts to the size and shape of the flange allowing a wide variety of uses including oil seals, engine housings and transmission flanges.

Activator 63 is a solvent-based product, specially formulated to promote the cure of Hernon Adhesives.

Activator 47 is solvent-free and designed to initiate the cure of Hernon toughened acrylic adhesives. Since Activator 47 contains no solvents, no waiting time for solvent evaporation is needed prior to assembly.

Hernon Activator 21 is an encapsulated catalyst that activates the resin Self Locker 523.

Cylinlock® 34323 is a fast curing, high-strength anaerobic adhesive yielding higher shear strengths with temperature resistance up to 300°F (149°C) It provides relatively quick cures, outstanding solvent resistance, and improved reliability for metal service applications.

Dissipator® 319 is a room temperature curing, two component thermal conductive epoxy adhesive for potting applications. Dissipator® 319 offers low viscosity for potting applications, is recommended for encapsulation of components that require heat dissipation and thermal shock properties. Dissipator® 319 features good thermal conductivity (1.1 W/mK to 1.4 W/mK)

Fusionbond® 371 is a two components methacrylate adhesive. It is specially formulated for structural bonding of thermoplastics, metal, wood and composite assemblies. Fusionbond® 371 is an excellent choice for composite bonding applications in the marine, automotive and construction industries because it requires virtually no surface preparation. Fusionbond® 371 provides toughness at temperatures from -67 to 250°F.

Blank Ammunition Sealant 53162 Is a medium viscosity, UV and LED curable compound formulated to provide high performance, fast curing, coating and sealing of ammunition blank tips. This product is also used for shallow potting applications.

Blank Ammunition Sealant 48641 Is a medium viscosity, UV and LED curable compound formulated to provide high performance, fast curing, coating and sealing of ammunition blank tips. This product is also used for shallow potting applications.

Activator 15 is a solvent free product which was designed to be used with React® 727, 784 and Fusionbond 374.

Tuffbond® 302 is a modified epoxy adhesive that provides a very fast room temperature cure. Tuffbond® 302 exhibits very good moisture chemical and heat resistance. This very fast cure epoxy adhesive is specially formulated for rapid in-line assembly of loud speakers. Tuffbond® 302 is also recommended for bonding metals, wood, ceramics, etc., and can be used for potting and encapsulation of electrical and electronic components.

Accelerator 58 is a single component non-CFC solvent-based product, formulated to provide a faster cure on acidic surfaces and cure excess Instantbond? cyanoacrylate adhesive outside the bond line. Accelerator 58 is used to increase the cure speed of Hernon® Instantbond® Adhesives. It is especially suited for post application on exposed Instantbond® adhesive outside of the bond line. Loudspeaker assembly and bonding jewelry are two examples.

Instantbond® 110 is a state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 110 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 110 can bond a wide variety of surfaces including thermoplastics, elastomers, ceramics, leather, cork, and paper, but is particularly suited for bonding metal substrates. Notwithstanding the superior bonding capability of Instantbond® 110, it is NOT recommended for long-term glass to glass bonding applications.

Instantbond® 112 is a low viscosity, state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 112 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 112 can bond a wide variety of surfaces including thermoplastics, elastomers, ceramics, leather, cork, and paper, but is particularly suited for bonding metal substrates. Notwithstanding the superior bonding capability of Instantbond® 112, it is NOT recommended for long-term glass to glass bonding applications.

Instantbond® 120 is a single-component cyanoacrylate adhesive suitable for applications where heat resistance is required. Instantbond® 120 resists thermal cycling and also exhibits superior resistance to humidity. Instantbond® 120 meets the requirements of CID A-A-3097 Type II, Class 3 and MIL-A-46050C TY II, CL 3.

Instantbond® 117 is a high viscosity, state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 117 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 117 can bond a wide variety of surfaces including metals, thermoplastics, elastomers, ceramics, leather, cork, and paper, but is particularly suited for wire tacking applications. Notwithstanding the superior bonding capability of Instantbond® 117, it is NOT recommended for long-term glass to glass bonding applications.

Instantbond® 113 is a state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 113 develops handling strength within seconds and full functional strength in a few hours. Instantbond? 113 can bond a wide variety of surfaces including metals, thermoplastics, elastomers, ceramics, leather, cork, and paper, but is particularly suited for bonding hard-to-bond plastics. Notwithstanding the superior bonding capability of Instantbond? 113, it is NOT recommended for long-term glass to glass bonding applications.

External Ammunition Sealant 76041 is a single component U.V. anaerobic sealant. 76041 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. It is specially formulated for pre-assembled components; it works by capillary action sealing ammunition and improving bullet pull force. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76041 is a low strength sealant that cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to five minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76061 is a single component U.V. anaerobic sealant. 76061 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. It is specially formulated for pre-assembled components; it works by capillary action sealing ammunition and improving bullet pull force. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76061 is a medium strength sealant that cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to five minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76060 is a single component U.V. anaerobic sealant. 76060 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. It is specially formulated for pre-assembled components; it works by capillary action sealing ammunition and improving bullet pull force. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76060 is a medium strength sealant that cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to five minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76040 is a single component, U.V curable anaerobic sealant. 76040 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. It is specially formulated for pre-assembled components; it works by capillary action sealing ammunition and improving bullet pull force. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76040 is a low strength sealant that cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to five minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76081 is a single component U.V. anaerobic sealant. 76081 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76081 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes. Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76084 is a single component U.V. anaerobic sealant. 76084 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76084 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76082 is a single component U.V. anaerobic sealant. 76082 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76082 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

External Ammunition Sealant 76083 is a single component U.V. anaerobic sealant. 76083 has a low viscosity penetrating material capable of bonding and sealing primers and case mouths in ammunition. This Sealant is specially formulated for Ammunition that needs greater fit tolerance and higher bullet pull forces. Curing occurs when the adhesive is applied between mating surfaces. The cured adhesive is a thermoset plastic and endures exposure to most solvents. Ammunition Sealant 76083 cures quickly at room temperature without the need for surface activators or heat to seal primer and case mouth assemblies. Fixturing strength develops in two to three minutes, Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 100 milliwatts/cm² to insure proper cure.

Supertacker® 67662 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 67662 provides a tough, waterproof bond that won’t crack or become brittle.

Porosity Sealant (HPS) 991 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The required addition of HPS Initiator 91 activates HPS 991R enabling the system to cure at elevated temperatures (HPS 991). The hardened resins exhibit superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic plastic molecules) in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage when exposed to elevated temperature to form tough cross-linked thermoset polymer, permanently sealing the workpiece. Residual adhesive film is water-washed from the part surfaces during rinsing. The parts leave the impregnating process without surface residue and can then be used in production immediately. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Dripstop® 920 is a general-purpose anaerobic pipe sealant which contains Teflon®. It has superior sealing and mild locking performance compared to tapes and non-hardening dopes. The properties of this Dripstop® prevents galling on Stainless Steel, Aluminum, and other metal pipe fittings. Dripstop® 920 reduces costs by eliminating leakage and increasing the assembly line speed. Dripstop® 920 seals to moderate pressure immediately and to 250 psig steam pressure in just 24 hours. This sealant also lubricates threads during make-up, prevents galling and assures smooth disassembly. UL Classification – File MH14222 Classified by Underwriters Laboratories Inc.® as to fire hazard only. 920 Pipe Sealant with Teflon®. Fire hazard is small. No flash point in liquid state. Ignition temperature 455°C (851°F). For use in devices handling gasoline, petroleum oils, natural gas (pressure not to exceed 300 psig), butane and propane not exceeding 2 in. pipe size. 29R9.