Formulations

Tuffbond® 394 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond® 394 will change from amber-yellow to a reddish brown upon cure. Bonding the voice coil to the cone has been a challenge for engineers, specifically when the adhesive temperature resistance requirement is above 200°F (93°C). Two component epoxy was commonly used for this application, but limitations such as mixing ratio, cure speed, potential solidification in equipment and the need for equipment flushing solvents have made Tuffbond® 394 more practical.

Tuffbond® 395 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond® 395 will change from amber to a reddish brown upon cure. Bonding the voice coil to the cone has been a challenge for engineers, specifically when the adhesive temperature resistance requirement is above 200°F (93°C). Two component epoxy systems have been most commonly used for this application, but limitations such as mixing ratio, cure speed, potential solidification in equipment and static mixers and the need for equipment flushing solvents have made Tuffbond® 395 more practical.

DEACTIVATOR FOR UV FOG, 500 GRAMS

CM8005 is a single-component room temperature cure gel-like anaerobic gasketing compound formulated to provide instant sealing capabilities. Once cured between mating metal flanges and filling voids in the surface, CM8005 provides a thin, flexible, solvent and temperature resistant seal.

Tuffbond® 313 adhesive/sealant is a two component, 100% solid system, one to one ratio, room temperature cure system. Tuffbond® 313 is recommended for bonding metals, wood, ceramics, etc., and can be used for potting and encapsulation of electrical and electronic components.

Primer 57 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 57 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Cleaner 62 is a non-aqueous, hydrocarbon based, non-CFC industrial solvent which removes oil and grease completely. This cleaning solvent prepares the surface for bonding with Hernon® Adhesives and Sealants. Cleaner 62 is recommended for final cleaning prior to assembling parts with Hernon® Adhesives and Sealants. It is not recommended for cleaning (flushing) equipment or for cleaning printed circuit boards and printed circuit assemblies.

Instantbond® 109 is a low viscosity, state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 109 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 109 can bond a wide variety of surfaces including thermoplastics, elastomers, ceramics, leather, cork, and paper, but is particularly suited for bonding metal substrates. Notwithstanding the superior bonding capability of Instantbond® 109, it is NOT recommended for long-term glass to glass bonding applications.

Nuts N’ Bolts® 431 is a wicking anaerobic used for preassembled equipment and structures where penetration into fastener connection points is required. This product allows very simple preventive maintenance by permitting thread locking without dismantling equipment. The product “wicks” into voids by capillary action. Use Nuts N’ Bolts® 431 to seal pores or pinhole porosity in welded seams, tanks, castings, or metal parts. The cured adhesive is a thermoset plastic suitable for temperatures up to 400°F (204°C), and exposure to most solvents.

Instantbond® 121 is a very high viscosity, state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 121 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 121 can bond a wide variety of surfaces including metals, thermoplastics, elastomers, ceramics, leather, cork, and paper. Notwithstanding the superior bonding capability of Instantbond® 121, it is NOT recommended for long-term glass to glass bonding applications.

Instantbond® 123 is a medium viscosity, state-of-the-art, single component, solventless, room temperature curing cyanoacrylate adhesive that polymerizes rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Instantbond® 123 develops handling strength within seconds and full functional strength in a few hours. Instantbond® 123 can bond a wide variety of surfaces including metals, thermoplastics, elastomers, ceramics, leather, cork, and paper. Notwithstanding the superior bonding capability of Instantbond® 123, it is NOT recommended for long-term glass to glass bonding applications.

Instantbond® 127 is a gel consistency single component, solvent-less, room temperature adhesive that sets in seconds when confined between two surfaces. The gel consistency allows for gap filling capability and prevents migration to unwanted areas.

Tuffbond® 305 is a modified epoxy adhesive that provides a very fast room temperature cure. Tuffbond® 305 exhibits very good moisture chemical and heat resistance. This very fast cure epoxy adhesive is specially formulated for rapid in-line assembly of loud speakers. Tuffbond® 305 is also recommended for bonding metals, wood, ceramics, etc., and can be used for potting and encapsulation of electrical and electronic components.

Nuts N’ Bolts® 128 is a single component, low strength thread locker designed for locking plastic and metal fasteners. Fixture time is about 5 minutes and adhesive can be pre or post applied. Any excess adhesive on the surface will cure and will not migrate to the other parts. Nuts N’ Bolts® 128 can be used as a low strength thread locker, bonder or tamper proofer for metal, polyester, nylon and many other thermo plastics materials.

Quantum® 156 is a single-component cyanoacrylate adhesive formulated for impact, thermal shock and peel resistance.

Porosity Sealant (HPS) 59801 is a low viscosity liquid sealant designed for sealing interfacial leak paths in flexible electronic assemblies. It may also be used to enhance dielectric strength or seal porosity in passive materials. The dual-cure system incorporated in HPS 59801 offers the advantage of elevated temperature curing or curing at room temperature. HPS 59801 is typically applied with a vacuum impregnation process that removes air from the internal void and then saturates the part with liquid sealant. In the absence of circulating air, the liquid rapidly polymerizes to form a tough, flexible, thermoset polymer that permanently seals gaps in the assembly. Excess liquid sealant is rinsed from the outside of the part with an aqueous solution effectively leaving no surface build up. Parts processed with HPS 59801 are sealed internally but remain cosmetically and dimensionally unchanged. Typical applications include sealing or unitizing over-molded electrical components against leakage of air, water, coolants, oils and other fluids. As a good insulator, HPS 59801 may also be used to improve the dielectric strength across gaps between high voltage conductors.

Mine Bonder 2000 is an anaerobic adhesive sealant which cures rapidly through large gaps with Hernon Primer 50 and will also provide rapid cure and dry fillets when exposed to high intensity ultraviolet light.

Nuts N’ Bolts® 423 is a single component anaerobic thread locking material, which is thixotropic and develops medium strength. The product cures when confined in the absence of air between close fitting metal surfaces and is particularly suitable for less active substrates such a stainless steel and plated surfaces.

Ultrabond® 3444 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 3444 is excellent for bonding and tacking many parts. Ultrabond® 3444 can also be cured with heat above 200°F (93°C) or Activator 56. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Hernon 397 is a single component, high temperature resistant, heat activated epoxy. It cures to a high-performance thermoset system with excellent adhesion properties to a wide variety of substrates. Tuffbond 397 will change from amber-yellow to a reddish brown upon cure. Product Benefits • High temperature resistance. • Single component (no mixing, no pot life). • Contains 150micron spacer beads for bond line control • Solventless. • Cures on demand (heat cure). • Will not slip during cure. • Changes color upon cure (yellow to brown). • Excellent adhesion to various substrates. • Gives high shear. • Low water absorption.

Hernon® Ultrabond® 750 is a UV curable adhesive that can be used to seal a variety of plastics when exposed to UV light. The sealant offers a water- tight seal with excellent environmental resistance. Prevents material escaping through a crimped seal. With Ultrabond 750 a low powered UV lamp (Blacklight), can be used to inspect for the presence of adhesive on the substrates. Product Benefits • UV fluorescence for in-process inspection •Cures well at 395nm •Flexible thermoset system • Excellent Water Resistance •Good adhesion to a variety of plastics • 100% solid system (no solvents) • Good gap filling properties • No shrinkage due to solvent evaporation • Rapid UV cure

Dissipator® 745 is a thermally conductive room temperature cure adhesive that is designed for bonding electrical components to heat sink with a controlled gap. Dissipator® 745, through a special shimming property, insulates the component electrically while allowing thermal conductivity. This special shimming feature produces a constant gap of 0.005 in. to 0.006 in. between components.

Nuts N’ Bolts® 227 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications.

Nuts N’ Bolts® 230 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N’ Bolts® 232 is a single component medium strength, anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N’ Bolts® 234 is a single component medium strength, anaerobic compound used to lock and seal coarse threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Nuts N’ Bolts® 237 is a single component, high strength, anaerobic compound used to lock and seal fine threaded nuts, bolts, and studs in a wide variety of applications.

Nuts N’ Bolts® 240 is a single component anaerobic compound used to lock and seal fine threaded nuts, bolts and studs in a wide variety of applications requiring easy removal or adjustment.

Nuts N’ Bolts® 425 is a single component anaerobic thread locking material, which is thixotropic and develops medium to high strength. The product cures when confined in the absence of air between close-fitting metal surfaces.

Nuts N’ Bolts® 246 is a single component anaerobic compound used to lock and seal coarse threaded nuts, bolts and studs in a wide variety of applications where removal with ordinary hand tools is necessary.

Ultrabond® 740 is formulated for bonding glass to glass or glass to metals. Ultrabond® 740 is excellent for bonding tacking and potting many parts. Ultrabond® 740 provides an excellent bond, high light transmittance and a refractive index like glass. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Tuffbond® 316 is a two component, room temperature cure system. By changing the ratio of resin and hardener, the cured adhesive can change from a tough and flexible to a hard and rigid system. Tuffbond® 316 is recommended for bonding metal, glass, wood, concrete, and rubber, and can be used for potting and encapsulation of electrical and electronic components.

Ammunition Primer Sealant 34194 is a single component 100% solid system offering a tough, dry coating with superior chemical and environmental resistance after cure. Ammunition Primer Sealant 34194 will cure rapidly when exposed to high intensity U.V. light. This coating is formulated to migrate rapidly resulting in complete coverage of the gap. The fluorescent sealant will offer an easy inspection using standard vision system.

Supertacker® 351 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 351 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 351 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.

Supertacker® 352 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 352 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 352 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.

Supertacker® 353 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 353 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 353 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.

Supertacker® 357 is a single component, high performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic composites, rubber, leather, wood and vinyl. Supertacker® 357 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 357 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.

Supertacker® 358 is a single component, high-performance elastomeric adhesive that exhibits exceptional bonding characteristics to a broad range of materials including metals, glass, plastic, composites, rubber, leather, wood and vinyl. Supertacker® 358 provides a tough, waterproof bond that won’t crack or become brittle. Supertacker® 358 out-performs silicones, acrylics, and rubber cement because it bonds to more surfaces with greater strength and durability.

Hernon Voice Coil Bonder 360 is a single component, black, heat cure adhesive formulated for bonding and coating voice coil components and high-temperature lamination. The cured bond withstands temperatures exceeding 600°F (316°C).

Copper Based Anti-Seize 367 is a low-friction, anti-seize lubricant manufactured from a combination of micro-size copper flakes and graphite dispersed in a water-resistant grease and fortified with antioxidants, plus rust and corrosion inhibitors. Copper Based Anti-Seize 367 provides a shield against metal-to-metal contact, preventing seizure and corrosion. It fills irregularities and imperfections and resists welding, hardening, or setting. Provides low friction and cushions impact and shock loads. Low shear between particles reduces stick-slip, allowing quick disassembly with minimum wrench torque. It will not squeeze out of the threads, gum up, or wash off.

Tuffbond® 47771 adhesive/sealant is a two-component epoxy. This adhesive is a 100% solid system, one to one ratio, room temperature cure system.

Porosity Sealant (HPS) 38374R is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. The required addition of HPS Initiator activates the dual-cure system enabling the system to cure anaerobically at room temperature or at elevated temperatures. The cured, hardened resin exhibits superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur (between metal grains or ceramic or plastic molecules) in the part are filled by low viscosity resin during vacuum application. Sealed micro-pores cure without shrinkage to a tough, cross-linked, thermoset polymer, permanently sealing the work piece. Residual adhesive film is washed from the part surfaces by water during the rinsing cycle. The parts leave the impregnating process without surface residue and can then be used in production within a short period of time. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating material (like acids) or painting prep solvents that could otherwise bleed out of the pores causing finishes to discolor, blister, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

HASA 39781 is a single-component, anaerobic, structural adhesive designed for bonding rigid assemblies. HASA 39781 cure is accomplished when mating surfaces including metal, glass and ceramics are joined together. Accelerated cures are possible with the application of primers or by a short, low temperature heat cycle. Upon cure, HASA 39781 is a highly crosslinked thermoset plastic with excellent properties over a wide range of conditions.

Grenade Igniter Case Sealant 40995 is a single component anaerobic thread locking and sealing adhesive. Grenade Igniter Case Sealant 40995 is a low viscosity penetrating material that works by capillary action between mating surfaces. The cured adhesive is a high-performance thermoset plastic suitable for temperatures up to 400°F (204°C). Grenade Igniter Case Sealant 40995 cures quickly at room temperature without the need for surface activators or heat to join threaded assemblies. Fixturing strength develops in five minutes, or within 10 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 60 milliwatts/cm² to insure proper cure.

Nuts N’ Bolts® 410 is a single component, low viscosity anaerobic adhesive/sealant designed especially for wicking applications. It has the ability to penetrate porous structures and cracks by capillary action, filling voids as large as 0.005 in.

UV FOG (Form on Gasket) 41764A is an EB/UV curable product that provides excellent adhesion to shaft seals, oil seals, metals, glass, ceramics and plastics. Can be used as a Form-in-place gasket in oil and coolant systems. Typical applications include Engine covers, Oil pans and other fluid seal systems.