Formulations

Dripstop® 929 is a general- purpose anaerobic pipe sealant. It has superior sealing and mild locking performance compared to tapes and non-hardening dopes. The properties of this Dripstop® prevents galling on Stainless Steel, Aluminum and other metal pipe fittings. Dripstop® 929 reduces costs by eliminating leakage and increasing the assembly line speed. Dripstop® 929 seals to moderate pressure immediately and to 250 psig steam pressure in just 24 hours. This sealant also lubricates threads during make-up, prevents galling and assures smooth disassembly. UL Classification – File MH14222 Classified by Underwriters Laboratories Inc.® as to fire hazard only. 929 Pipe Sealant with Teflon®. Fire hazard is small. No flash point in liquid state. Ignition temperature 455°C (851°F). For use in devices handling gasoline, petroleum oils, natural gas (pressure not to exceed 300 psig), butane and propane not exceeding 2 in. pipe size. 29R9.

Powerseal 932 is a single component, non-hardening, non-curing gray paste pipe sealant which lubricates and seals threaded pipe connections and O-Rings. Powerseal 932 is unaffected by water, oil, ammonia, glycerin, steam, all types of gases, exhaust fumes and most hard- to- hold liquids. Powerseal 932 withstands extreme temperatures and pressures and will not shrink, crack, or crumble. The product remains pliable and will not harden, making connection vibration proof. It makes for easy assembly and makes disassembly and repair simple. It also prevents corrosion and seizing of metal parts.

Dripstop® 943 is an adhesive/sealant specifically formulated for the sealing and mild locking of Hydraulic and Pneumatic threaded parts. Dripstop® 943 will positively seal pipe threads, standard nuts and bolts, fittings for hydraulic and pneumatic systems, air conditioners, fittings for refrigeration equipment, and all types of water and chemical-processing, valves and equipment, including steam up to 300°F. Dripstop® 943 is a single component anaerobic adhesive/sealant. This adhesive will provide a rapid cure at room temperature. Upon cure, the material becomes a highly crosslinked thermoset plastic which will prevent leakage from shock, and vibration, as well as corrosive liquids and atmospheres.

Dripstop® 945 is a high-performance adhesive/sealant specifically formulated for the sealing and mild locking of hydraulic and pneumatic threaded parts used with hydraulic and pneumatic equipment. Dripstop® 945 will seal pipe threads, standard nuts and bolts, fittings for hydraulic and pneumatic systems, air conditioners, fittings for refrigeration equipment, and all types of water and chemical processing valves and equipment, including steam up to 350°F. Dripstop® 945 is a single component, anaerobic adhesive/sealant, which will provide a rapid cure at room temperature. Upon cure, Dripstop® 945 becomes a highly crosslinked thermoset plastic preventing leakage from shock, vibration as well as corrosive liquids and atmospheres.

Dripstop® 946 is a high-performance adhesive/sealant specifically formulated for the sealing and mild locking of hydraulic and pneumatic threaded parts used with hydraulic and pneumatic equipment. Dripstop® 946 will seal pipe threads, standard nuts and bolts, fittings for hydraulic and pneumatic systems, air conditioners, fittings for refrigeration equipment, and all types of water and chemical processing valves and equipment, including steam up to 300°F. Dripstop® 946 is a single component, thixotropic (non-migrating) anaerobic adhesive/sealant, that does not contain PTFE, and will provide a rapid cure at room temperature. Upon cure, Dripstop® 946 becomes a highly crosslinked thermoset plastic preventing leakage from shock, vibration as well as corrosive liquids and atmospheres.

Dripstop® 947 is a high-performance adhesive/sealant specifically formulated for the sealing and mild locking of hydraulic and pneumatic threaded parts used with hydraulic and pneumatic equipment. Dripstop® 947 will seal pipe threads, standard nuts and bolts, fittings for hydraulic and pneumatic systems, air conditioners, fittings for refrigeration equipment, and all types of water and chemical processing valves and equipment, including steam up to 350°F. Dripstop® 947 is a single component, thixotropic (non-migrating) anaerobic adhesive/sealant, that does not contain PTFE, and will provide a rapid cure at room temperature. Upon cure, Dripstop® 947 becomes a highly crosslinked thermoset plastic preventing leakage from shock, vibration as well as corrosive liquids and atmospheres.

Porosity Sealant (HPS) 990 is the solution to leak proof parts, improving machinability, in addition to increasing the durability and surface quality for painting and plating. HPS 990 is also excellent for sealing leak paths in rigid electronic assemblies. The hardened resins exhibit superior chemical resistance and elevated temperature stability. The microscopic voids, where potential leaks occur in the part are filled by the low viscosity resin during vacuum application. Sealed micropores cure without shrinkage to form tough cross-linked thermoset polymer, permanently sealing the piece. Excess residual adhesive is washed from the part surface during rinsing with water. The parts leave the impregnating process without surface residue and can then be used in production within a few short hours. The resin polymerizes, sealing gaps in any assembly. This protects electrical components against leakage from air, water, coolants and oils. When used in preparation for plating or painting processes, the impregnation process also eliminates absorption of plating materials (like acids) or painting prep solvents that could otherwise later bleed out of pores causing finishes to discolor, bleed, pit or peel. Sealed powdered metal parts exhibit better machinability, enhanced tool life and better dimensional control.

Tuffbond® 318 is a modified epoxy adhesive that provides a fast room temperature cure. Tuffbond® 318 exhibits very good moisture chemical and heat resistance. This fast cure epoxy adhesive is specially formulated for rapid in-line assembly of loud speakers. Tuffbond® 318 is also recommended for bonding metals, wood, ceramics, etc., and can be used for potting and encapsulation of electrical and electronic components.

Chemical Stripper 30 is a chemical liquid that works to remove pre-cut conventional gasket cements as well as formed in place chemical gaskets. Chemical Stripper 30 lifts off baked-on gaskets, gasket cements, formed-in-place gaskets, carbon deposits, dried oil, grease and paint on any type of metal in minutes. Also suitable for use on wood. It is packaged in a convenient spray liquid that penetrates and cleans intricate shapes, but will not run off, even on vertical surfaces.

Hernon® HPS Initiator 91 is used to activate Hernon® Hernon Porosity Sealant (HPS) resins. Hernon® HPS Initiator 91 activates HPS 991R enabling the system to cure at elevated temperatures.

Rust Inhibitor 40 is an effective corrosion remover and rust preventative which leaves a protective finish for up to 1 year. Produces a clean, dry surface that can be painted, plated or powder coated afterward with no pre-cleaning. Not for use with zinc plated or magnesium items. Rust Inhibitor 40 is used on rusted steel when only a minimum surface preparation is practical. Rust Inhibitor 40 protects, cleans and leaves a protective coating.

Primer 46 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 46 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C.

Grenade Igniter Case Sealant 47422 is a single component UV and anaerobic curing adhesive. Grenade Igniter Case Sealant 47422 is a low viscosity penetrating material that works by capillary action between mating surfaces. The cured adhesive is a high performance thermoset plastic suitable for temperatures up to 400°F (204°C). Grenade Igniter Case Sealant 47422 cures quickly at room temperature without the need for surface activators or heat to join assemblies. Fixturing strength develops in five minutes, or within 10 seconds by exposing the edge fillets to high intensity long wavelength UV light (365 nm). Full strength will be reached in 24 hours. Cure fillets at UV light irradiances above 60 milliwatts/cm² to insure proper cure.

UV FOG (Form on Gasket) 68221 is an EB/UV curable product that provides excellent adhesion to shaft seals, oil seals, metals, glass, ceramics and plastics. Can be used as a Form-in-place gasket in oil and coolant systems. Typical applications include Engine covers, Oil pans and other fluid seal systems.

Ultrabond® 3443 is a single component, tri-cure conformal coating formulated for bonding glass to glass or glass to metals. Ultrabond® 3443 is excellent for bonding and tacking many parts. Ultrabond® 3443 can also be cured with heat above 200°F (93°C) or Activator 56 or 59. Exposure to a high intensity UV light will cure these adhesives to a dry, hard surface.

Nuts N’ Bolts® 427 is a single component anaerobic thread locking material, which develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces.

SelfSealer® 622 is a tough, pre-applied, non-hardening threaded sealant. SelfSealer® 622 provides an instant seal on different pipe threads and can be used up to eight (8) times without recoating. SelfSealer® 622 is water based, non-toxic, safe and can be applied easily without special handling precautions. SelfSealer® 622 provides resistance to vibrational loosening because of its prevailing torque characteristics. Therefore, it is very effective on non-locking applications.

Hernon® Blank Ammunition Sealant 48643 is a higher viscosity, UV and LED curable compound formulated to provide high performance, fast curing, coating, and sealing of ammunition blank tips. This product is also used for shallow potting applications. Product Benefits • UV fluorescence for in-process inspection • LED curable • NO Solvents 100% solid system • Excellent ula. adhesion to a variety of surfaces • Excellent environmental resistance • Good gap filling properties • No shrinkage due to solvent evaporation • Rapid room temperature cure