Formulations

Nuts N’ Bolts® 410 is a single component, low viscosity anaerobic adhesive/sealant designed especially for wicking applications. It has the ability to penetrate porous structures and cracks by capillary action, filling voids as large as 0.005 in.

Nuts N’ Bolts® 420 is a single component anaerobic thread locking material, which is thixotropic and develops low strength for easy disassembly. The product cures when confined in the absence of air between close fitting metal surfaces.

Nuts N’ Bolts® 423 is a single component anaerobic thread locking material, which is thixotropic and develops medium strength. The product cures when confined in the absence of air between close fitting metal surfaces and is particularly suitable for less active substrates such a stainless steel and plated surfaces.

Nuts N’ Bolts® 425 is a single component anaerobic thread locking material, which is thixotropic and develops medium to high strength. The product cures when confined in the absence of air between close-fitting metal surfaces.

Nuts N’ Bolts® 427 is a single component anaerobic thread locking material, which develops high strength. The product cures when confined in the absence of air between close fitting metal surfaces.

Nuts N’ Bolts® 428 is a single component anaerobic threadlocking compound designed for heavy duty applications subject to operating temperatures to 450°F (232°C). The product delivers high strength locking and sealing on screws, nuts, bolts, studs and fittings. Excellent break-loose and prevailing torque values assure maximized resistance to transverse vibration loosening at elevated temperatures. Meets requirements of CID A-A-59720 Grade HT

Nuts N’ Bolts® 429 is a single component anaerobic thread locking adhesive. Nuts N’ Bolts® 429 is a high-strength adhesive for locking and sealing large bolts and studs 1inch and larger diameters. Curing occurs only when adhesive is confined between mating surfaces. The cured adhesive is suitable for temperatures up to 300°F (149°C) and exposure to most solvents.

Nuts N’ Bolts® 431 is a wicking anaerobic used for preassembled equipment and structures where penetration into fastener connection points is required. This product allows very simple preventive maintenance by permitting thread locking without dismantling equipment. The product “wicks” into voids by capillary action. Use Nuts N’ Bolts® 431 to seal pores or pinhole porosity in welded seams, tanks, castings, or metal parts. The cured adhesive is a thermoset plastic suitable for temperatures up to 400°F (204°C), and exposure to most solvents.

Weld Sealant 433 is a single component anaerobic penetrating adhesive and sealant. Utilizing capillary action, Weld Sealant 433 penetrates and seals porosities and cracks as large as 0.127 mm. Once confined away from air Weld Sealant 433 cures to a thermoset plastic. Sealant remaining on the surface will not cure and can be easily wiped clear. Benefits include retention of fluids and pressures as well as corrosion and contamination elimination. Temperature resistance is up to 400°F (204°C). Weld Sealant 433 is impervious to most solvents. Welds, castings and powder metal parts can be sealed to their rupture pressure.

Nuts N' Bolts® 434 is a thixotropic, 100% active anaerobic compound which solidifies with reliable and expected strength upon application to most fasteners. Particularly suitable for applications on less active substrates such as stainless steel and plated surfaces, where disassembly with hand tools is required for servicing. Nuts N' Bolts® 434 is easily applied. No mixing (single component), no curing outside the joint and no torque adjustments are necessary. Nuts N' Bolts® 434 offers increased profitability, having approximately 80% cost advantage over the cheapest mechanical methods as well as reducing inventories, maintenance, and the need for costly precision tolerances. Nuts N' Bolts® 434 can be used on up to 3/4inch bolts with light oil contamination.

Nuts N’ Bolts® 97860 is a wicking anaerobic used for preassembled equipment and structures where penetration into fastener connection points is required. This product allows very simple preventive maintenance by permitting thread locking without dismantling equipment. The product “wicks” into voids by capillary action. Use Nuts N’ Bolts® 97860 to seal pores or pinhole porosity in welded seams, tanks, castings, or metal parts. The cured adhesive is a thermoset plastic suitable for temperatures up to 400°F (204°C), and exposure to most solvents.

Powerseal 932 is a single component, non-hardening, non-curing gray paste pipe sealant which lubricates and seals threaded pipe connections and O-Rings. Powerseal 932 is unaffected by water, oil, ammonia, glycerin, steam, all types of gases, exhaust fumes and most hard- to- hold liquids. Powerseal 932 withstands extreme temperatures and pressures and will not shrink, crack, or crumble. The product remains pliable and will not harden, making connection vibration proof. It makes for easy assembly and makes disassembly and repair simple. It also prevents corrosion and seizing of metal parts.

Primer 37824 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 37824 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Primer 46 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 46 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C.

Primer 49 is a single component, non-CFC solvent based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 49 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C. Primer 49 meets the requirements of MIL-S-22473E (Grade T) and ASTM D5363 (Grade T).

Primer 50 is a single component, non-CFC solvent-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 50 is used where increased cure speed of Hernon® anaerobic adhesives and sealants is required. It is especially recommended for applications with passive metals or inert surfaces and with large bond gaps. It is particularly recommended for cure conditions below 15°C. Primer 50 meets the requirements of ASTM D5363 (Grade N) and MIL-S-46163A Grade F.

Primer 57 is a single component, solvent-free, reactive monomer-based product designed to promote the cure speed of Hernon® anaerobic adhesives and sealants. Primer 57 is used where increased cure speed of Hernon® anaerobic products is required, and for difficult to bond applications where galvanized steel or zinc electroplated surfaces are involved. This product was specially formulated for increasing bond integrity on dichromated surfaces.

Quantum® 124 is a surface insensitive cyanoacrylate adhesive formulated to improve adhesion properties and fixture time as well as gap filling capabilities over conventional cyanoacrylate adhesives. This advanced formulation improves adhesion to difficult to bond plastics, wood, leather, ceramics, elastomers, and acidic surfaces such as freshly plated components. Quantum® 124 is a state-of-art single component, solventless, room temperature curing adhesives that polymerize rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Quantum® 124 will develop handling strength within seconds and full cure within a few hours.

Quantum® 138 is a surface insensitive cyanoacrylate adhesive formulated to improve adhesion properties and fixture time as well as gap filling capabilities over conventional cyanoacrylate adhesives. This advanced formulation improves adhesion to wood, leather, ceramics, elastomers, and acidic surfaces such as freshly plated components. Quantum® 138 is a state-of-art single component, solventless, room temperature curing adhesives that polymerize rapidly when pressed into a thin film between parts. The presence of surface moisture commences the cure of the adhesive. Quantum® 138 will develop handling strength within seconds and full cure within a few hours.

Quantum® 156 is a single-component cyanoacrylate adhesive formulated for impact, thermal shock and peel resistance.